text.skipToContent text.skipToNavigation

Heat Flux Sensors for Heat Transfer Measurements

Economical heat flux sensor

(0)

Data Sheet (PDF)

$386.79

Item# HFS-5

Volume discounts available

Volume Discount Schedule

Quantity	Price each
1-9	$386.79
10-24	$367.45
25-49	$359.71
50-99	$344.24
100-199	$336.51
200+	$328.77

QTY

Added to Your Shopping Cart

In stock

Lead Time (If not in stock): 3 weeks

+ Add to Project List

HFS-5 Economical sensor for use in R&D heat transfer measurements and thermal systems evaluation
HFS-6 Larger sensor for use in buildings thermal evaluation and higher sensitivity
UHFS-09 Larger sensor, highest sensitivity and waterproof for use in geothermal studies
HFS DAQ as the accessory of HFS series, low-cost data acquisition system to accurately measure the signals outputted from HFS heat flux sensors and their integrated thermocouples
For sensor application we suggest OMEGATHERM™ High Temperature and High Thermally Conductive Paste

View Specs

HFS-5 Model Options

View all models

Edit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.

*Highlighted options are not compatible. Please select a different combination.

Process Temperature Range

Encapsulation Material

Nominal Sensitivity

Sensor Thickness

Specific Thermal Resistivity

Absolute Thermal Resistance

Heat Flux Range

Response Time

Sensing Area Dimensions

Total Sensor Dimensions

Sensing Area

Total Sensor Area

What data logger can be used with your heat flux sensors?

Asked by: Navid93

Thank you for the inquiry. We have the new Layer N system with SP-016-1. Part of the modular Layer N system; https://www.omega.com/en-us/layer-n/smart-probes/p/SP-016-Series Best regards OMEGA

Answered by: AENwlk

Date published: 2020-10-06

If I need to calculate the total heat power through HFS-5, should I multiply the measured heat flux with sensor area (6.5cm2) or total area (9.2cm2)?

Asked by: han2021

Hi Han2021 Thank you for the inquiry. Please forward this question to TEMP@OMEGA.CON. Best regards OMEGA

Answered by: NorwalkAE_RS

Date published: 2022-05-17

What is the maximum sampling rate for the HFS-5?

Asked by: Trevor42

Hi Trevor C Thank you for the inquiry. Sample rate would be determined by the instrumentation used. Response time of the sensor is 0.6 seconds as noted on the data sheet. Best regards OMEGA

Answered by: NorwalkAE_RS

Date published: 2022-05-17

What is the output voltage range for HFS5?

Asked by: Trevor42

Hi Daniel18 Just under 1 mv at max heat flux. You'll need a meter with micro volt level resolution. Best regards, OMEGA

Answered by: NorwalkAE_RS

Date published: 2021-12-23

Can the HFS-5 heat flux sensor be used outside in the weather?

Asked by: Trevor42

Hi Trevor42 Thank you for the inquiry. This sensor is not suitable for outdoor weather conditions. Best regards, OMEGA

Answered by: NorwalkAE_RS

Date published: 2022-01-24

What is the core material (dark brown) in the HFS-5 sensor and whether it distributes the heat laterally?

Asked by: han2021

Hi Han2021, Please forward this question over to our temperature group for review; TEMP@OMEGA.COM Best regards OMEGA

Answered by: NorwalkAE_RS

Date published: 2022-05-17

we are using the HFS-5 Heat Flux+ T type Thermocouple sensor and the HFS-DAQ. I need to add 8' of length to the wire leads of the sensor to reach our test location. Do you sell these as integral cables? if not, can you suggest extension cables? Thanks

Asked by: Keithgm

Hi Keithgm, Thank you for the inquiry. We d not offer integrated cable unfortunately. For the thermocouple side; You'll need type T extension wire similar to https://www.omega.com/en-us/temperature-measurement/temperature-wire-and-cable/thermocouple-wires/extt-tx-wire/p/EXTT-T-24-25. For the heat flux side you can use 2 conductor instrumentation wire (copper). Best regards OMEGA

Answered by: NorwalkAE_RS

Date published: 2022-08-23