Pressure Snubbers to Protect Against Pressure Surges
1/4" NPT, 10,000 psi Max. Pressure, for Air, Steam and gases
Volume discounts available
Volume Discount Schedule
| Quantity | Price each |
|---|---|
| 1-9 | $19.49 |
| 10-24 | $18.52 |
| 25-49 | $18.13 |
| 50-99 | $17.35 |
| 100+ | $16.96 |
Added to Your Shopping Cart
Configuration complete.
Please add to cart to keep it or exit the configuration
Please add to cart to keep it or exit the configuration
Failed to Save Configurations, Click on Configure Button Start Again
- Protects Transducers, Gauges and Switches from Pessure Spikes, Surges and Water Hammer
- Available in 1/8, 1/4, or 1/2 NPT Fittings
- Three Different Porosity Ratings Suitable for Most Media
- All Stainless Steel Construction
PS-4G Model Options
View all modelsEdit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.
*Highlighted options are not compatible. Please select a different combination.
Media Type
Pressure Port Type
Pressure Port Size
Max Pressure
Features
Snubber Types
Wetted Materials
PRESSURE SNUBBER - for dampening and filtering. The snubber has a porous metal disc available in three standard grades of porosity. Due to the large filter surface the snubber has less tendency to clog than orifice type devices. The housing is 303SS and the filter disc is 316SS with a maximum PSI rating of 10 000 at 25°C. (PS-8 series 5000 PSI)
Please note that the finish of pressure snubbers may vary. The flat surfaces on snubbers you receive may have a smooth and machined appearance or they may have a textured, shot-peened appearance. These are merely cosmetic differences that do not affect the functionality and performance of the product.
Rated 5 out of
5
by
Acer from
Presurre snubber
This is a beautifully made and designed product at a very reasonable price.
It works as advertised. My use is in the manifold pressure measuring system of a Garmin engine monitor.
The pressure reading is very steady with the addition of the Omega snubber. It should be required with all Garmin engine monitors.
Date published: 2017-02-20
Rated 5 out of
5
by
Recreational from
Perfect for my boost gauge
Fixed my flutter in my boost gauge installed on my 2001 cummins powered RV
Date published: 2017-06-22
Rated 4 out of
5
by
Rvator from
Stable
Used to stabilize manifold pressures that were fluctuating over two inches. Brought it down to .1 movement.
Date published: 2018-02-25
Rated 5 out of
5
by
Anonymous from
cost affective
Worked to perfection. Makes flowline testing a cinch.
Date published: 2020-07-07
Rated 5 out of
5
by
Rick G from
Reduce pressure sensor failures
Snubbers are the perfect fit for systems where the sudden inrush of water is a problem and could damage gauges, transducers or pressure switches or cause erratic behaviour. These were used on a 15HP submersible well pump transducer
Date published: 2020-05-02
Rated 5 out of
5
by
rollie from
stopped pressure fluctuations
My digital manifold pressure sensor requires this part, without it my manifold pressure gauge was constantly fluctuating, about +/- 3". Now that I installed the snubber my pressure gauge is rock steady.
Date published: 2018-11-14
Rated 5 out of
5
by
freeflight1 from
Worked great
This snubber calmed my gauge fluxuations as expected
Date published: 2018-07-25
Rated 5 out of
5
by
Coop from
Functions exactly as expected
Gauge needle would bounce drastically above 20 psi prior to installing pressure snubber. Afterward gauge needle doesn't bounce, so pressure snubber works exactly as it is supposed to
Date published: 2017-08-19
For a pressure transducer operating in a mixed environment (gas and liquid) what would be the best choice?
Thank you for your inquiry, the PS-4G would work best in this application
Date published: 2022-02-07
can a PS-4G be cleaned if it is contaminated
Thank you for your inquiry, due to the cost of the PS-4G we would recommend that you replace it.
Date published: 2022-09-23
Does it matter which direction the PS-4G snubber is installled in a Manifold Pressure Line?
Thank you for your inquire.
The snubber needs to be in the positive direction. It will not work if its used in a vacuum.
Hope this was helpful
Date published: 2022-10-31
Does it matter if the positive pressure flows into the male end, or the female end?
Positive flow should be going from female end outward
Date published: 2022-10-31