Self-Adhesive Polyimide Fast Response RTD Surface Sensors, Class A Accuracy
SA1-RTD Surface-Mount RTD Temperature sensor | Quick Shipment
Volume discounts available
Volume Discount Schedule
| Quantity | Price each |
|---|---|
| 1-9 | $163.25 |
| 10-24 | $155.09 |
| 25-99 | $146.93 |
| 100-499 | $138.76 |
| 500-999 | $130.60 |
| 1000+ | $122.44 |
Added to Your Shopping Cart
Configuration complete.
Please add to cart to keep it or exit the configuration
Please add to cart to keep it or exit the configuration
Failed to Save Configurations, Click on Configure Button Start Again
- 100 Ω DIN Class A (±0.06 Ω or ±0.15°C at 0°C) Accuracy Standard
- Easy-Installation Silicone-Based, Self-Adhesive Backing Rated to 260°C (500°F)
- Back Can be Reapplied
- Temperature Range -73C to 260°C Continuous, 290°C (554°F) Short Term Operation When Installed with OMEGABOND Air Set Cements
- Stripped 3-Wire Leads Standard (Connectors Optional), Color Code: Black/Black/Red
- Optional 4-Wire Configuration (Color Code: Black/Black/Red/Red)
- Stocked in 1 m (40") Lengths Also Available in 2 and 3 m (80 and 120") and Custom Length Lead Wires
- Other Resistances/Accuracies Available on Request
- Stainless Steel Overbraid Option to reduce electrical noise and protect lead wire from abrasion
- Intended for one-time placement on surface
SA1-RTD-4W-120-TA4F Model Options
View all modelsEdit these specs to order a different model. Not all combinations are valid. Options compatible with previous selections will be in bold.
*Highlighted options are not compatible. Please select a different combination or click the CONFIGURE button to build your own.
Number of Wires
Cable Insulation
Termination Connection Type
Cable Length
Category
Process Temperature Range
Sensor Application
Nominal Resistance
Accuracy
Mounting Style
Maximum Temperature Measurement
Minimum Temperature Measurement
The SA1-RTD surface-mount RTD temperature sensor mounts on flat or curved surfaces and provides Class A accuracy for critical temperature monitoring applications. Based on a 2 x 2 x 0.8 mm thin-film platinum RTD and supplied with bare 3-wire leads as a standard configuration (connector optional), itcan be customized for use in a wide variety of applications. The sensor can be easily applied with its selfadhesive
backing, or positioned permanently with OMEGABOND™ cements.
Use the SA1-RTD to monitor chip, heat sink, and environmental temperatures in electronic devices; check piping or ducting temperatures;monitor motor and transformer core heat; test insulation capabilities; and check other applications in which surface and/or gradient temperatures need to be monitored or controlled.
Rated 5 out of
5
by
SolarCowboy from
BOM sensor
I ordered temperature sensors to monitor solar panels temperature to analyze performance
Date published: 2016-10-23
Rated 4 out of
5
by
Peter R from
Works great
Does exactly what it says it does. Installed easily with epoxy from omega. Plenty accurate for our purposes. Cost effective
Date published: 2017-02-28
Rated 5 out of
5
by
AndyL from
Good RTDs
RTDs are performing well, as expected. No issues regarding quality or anything else.
Date published: 2022-08-08
Rated 5 out of
5
by
Gardenerbob from
Easy to use RTD with self adhesive
Easy to use RTD with self adhesive that can conform to the curved surface of piping.
Date published: 2021-05-06
Rated 5 out of
5
by
PV Tech from
Excellent Turn-Around Time
Amazed at the extremely short-lead time. It arrived prior to the expected arrival time, and kept the project it was needed for Operationally Ready prior to the Completion Timeline.
Date published: 2021-03-24
Rated 1 out of
5
by
Lincoln from
Didn't stick well
The adhesive melted well before the stated temperature limit
Date published: 2020-04-17
Rated 5 out of
5
by
Snaucler from
As Advertised
I have used these on several projects, and the work exactly as advertised. I have not had a problem with any of them.
Date published: 2018-01-25
I'm interested in purchasing one of these, but I can't find information regarding acceptable current bounds; can you give me an estimate on minimum required current to operate this sensor, and maximum not to toast it?
Hi EAML
Thank you for the inquiry. 1 mA or less is the specified current level. A higher current can lead to self heating error and should be avoided.
Lower current levels can be used and the level is determined by the instrumentation used.
We do not have a specification on mA levels which can damage the sensor.
Best regards
OMEGA
Date published: 2020-06-10
What are the color codes of the 3 wires?
Thank you for your inquiry. The color code is 1 Red Wire & 2 Black Wires.
Date published: 2022-06-20
It says, 'back can be reapplied' in the product description. Is there back adhesive material that can be used for this RTD?
The SA1-RTD if carefully removed can be reattached but each time will lose some of its adherent properties. Sometimes when it no longer sticks a piece of Kapton tape can be laid over the top to hold it in place,
Date published: 2020-04-15
Hi, could you please send me or link here a "Resistance vs Temperature table" for the SA1-RTD (3 wires)? Regards.
Thank you for your inquiry Sborzy. Please review the following link for the table: https://assets.omega.com/tech-ref-legacy-pdfs/z252-254.pdf
Date published: 2022-08-25
What is the best method to cut the PFA wire covering to get access to more of the leads?
Omega sells the TW-6 which is designed to remove the outer insulation of wires with ease. You can enter TW-6 in the search box on Omega's web page for further details.
Date published: 2020-05-11
What are the dimensions (width and thickess) of the cable?
Thank you for your inquiry Dave Z. The wire gauge of this sensor is 26 AWG. It has a nominal size of 0.060" x 0.064".
Date published: 2022-08-25
Does anybody have a recommendation for temperature sensing device to connect to this sensor? One that could connect to a computer, ideally.
You may want to consider the SA1-RTD-80 with the HH804U handheld meter along with the software HH800-SW (windows software and USB cable) which allows for real time data logging to a PC.
For extensive data logging a DC power jack is available
HH804U Meter $173.88 each in stock
Comes complete with HH804-CONNECTOR (one per channel), protective rubber boot,
NIST certificate (no points), 4 “AAA” batteries, and operator’s manual.
https://www.omega.com/en-us/sensors-and-sensing-equipment/temperature/thermometers/p/HH804-805
HH800-SW $23.18 in stock
Windows software and USB cable (USB models only)
https://www.omega.com/en-us/sensors-and-sensing-equipment/temperature/thermometers/p/HH800-SW
HH800-ADAPTOR $20.09 each in stock
https://www.omega.com/en-us/sensors-and-sensing-equipment/temperature/hygrothermometers/p/HH800-ADAPTOR
If a thermocouple can be considered in place of a RTD , for example the SA1-K-72- SRTC is a good option. We offer the Thermocouple Data logger with USB interface the OM-EL-USB-TC which accepts a J, K or T type thermocouple. This plugs directly into a USB Port – No USB cable is required
https://www.omega.com/en-us/control-and-monitoring-devices/data-loggers/p/OM-EL-USB-TC-Series
and the specifications sheet is: https://br.omega.com/omegaFiles/das/pdf/OM-EL-USB-TC.pdf
Thank you for your question.
Date published: 2022-02-07
The data sheet mentions installation using Omegabond thermal epoxy. What is the correct/recommended process for epoxy install? Does the polyimide tape get completely removed, and then epoxy the RTD on? Seems like tape on epoxy would not create a good bond
Thank you for your inquiry RPeebs. You will need to use thermal conductive epoxy that way you don't block the heat from coming into contact with the probe. The pad should not affect the temperature measurement if you decide to use epoxy in conjunction with the adhesive pad.
Date published: 2022-08-25
SA1-RTD Surface-Mount RTD Temperature sensor | Quick Shipment
$163.25
0 In Stock
